EN 1335 is the European standard for office work chairs. It is quoted in almost every European tender, yet it is frequently misunderstood: it is not a certificate, it is not a CE mark, and holding a report does not automatically make a chair compliant for every market. Here is what the three parts actually cover.
The three parts
EN 1335 is published in three parts, and a complete test report should reference all three:
- EN 1335-1 – Dimensions. Defines the dimensional requirements and the size designation of office work chairs. The current edition designates three sizes (A, B and C), based mainly on seat height range and user stature. A buyer should state the size required, because the same model line can be supplied in different sizes.
- EN 1335-2 – Safety requirements. Covers stability, strength, edges and entrapment risks. This is the part that matters when a market-surveillance authority or an insurer asks whether the chair is safe.
- EN 1335-3 – Test methods. Describes how each test in part 2 is performed. The lab must state that it tested to this part, otherwise the results cannot be compared with another supplier’s report.
What is actually tested
Broadly, the test programme covers:
- Stability – forward, sideways and rearward, with and without a loaded seat.
- Seat and back static load – a defined force applied to the seat and to the backrest.
- Cyclic durability – repeated loading of the seat and back to simulate years of use.
- Armrest strength – vertical and horizontal forces, plus a durability cycle.
- Base and castor endurance – including a rolling test over an obstacle.
- Entrapment and sharp edges – a visual and dimensional check, not a machine test.
The exact forces, cycles and tolerances are defined in the standard. When you compare two test reports, compare the clause numbers and the edition, not just the word “passed”.
Is EN 1335 mandatory?
No – not in the sense that customs will stop a container without it. There is no CE marking for office chairs, because seating is not covered by a CE directive. What applies instead is general product safety law: in the EU, the General Product Safety Regulation requires that consumer products placed on the market are safe, and a test to a harmonised or recognised standard is the normal way to demonstrate that.
In practice, EN 1335 becomes mandatory through the buyer, not through the law:
- public procurement and EU green public procurement criteria reference it;
- large corporate buyers and facility managers require a report before approving a supplier;
- insurers and warranty providers ask for it after an incident.
What a usable report contains
- The standard and the edition tested (for example EN 1335-1:2020 / -2 / -3).
- The model, size designation and a photo or drawing of the tested sample.
- The laboratory’s ISO/IEC 17025 accreditation scope, or a clear statement that the test is within it.
- Clause-by-clause results, not a single “pass” line.
- The date, and whether the report covers a production sample or a prototype.
Practical advice for buyers
Ask for the report before the sample, not after. A lab test takes two to four weeks plus shipping, and a report issued for a prototype does not automatically cover a later change of mechanism, base or foam. If the supplier changes a component after testing, ask whether the report still applies – and get the answer in writing.
How long testing takes, and what it costs
A full EN 1335 programme on one model normally takes two to four weeks in the laboratory, plus shipping of the sample. Cost depends on the number of tests requested and on whether the lab has to build test fixtures for a specific base or armrest. Laboratories quote per model, and a re-test after a design change is a new quote – which is why the specification should be frozen before testing starts.
Two practical notes: the sample must be a production-representative unit, and the report is issued to the company that ordered it. If you want the report in your own company name, say so before the order is placed.
What usually fails first
When a chair fails EN 1335, it is rarely the seat foam. In our experience the sequence is:
- Base and castor endurance – a PP base that is fine in a showroom can crack under the cyclic test if the material grade is wrong.
- Armrest static load – especially on chairs where the armrest is fixed to the back frame rather than to the seat plate.
- Backrest strength – usually a frame thickness issue, not a mesh issue.
- Stability – often the result of a smaller base radius paired with a high back.
All four are design decisions, not manufacturing defects. That is why a test report is worth having before the mould is finalised rather than after the first container.
EN 1335 and the tender document
When a European public buyer writes “EN 1335”, they usually mean the chair must be tested to all three parts and the report must be available on request. Some tenders additionally specify the size (A, B or C) and a minimum seat height range. Read the tender for those two details before quoting – a chair that passes the test but is the wrong size class is still non-compliant.
Ask about EN 1335 testing for your order